1User and Installation ManualThe home theater projectorHT300 E-LINK cod.46.0421.000
10CAUTION: In the case of ceiling or wall mounting using a suspension bracket, follow the instructions carefully and comply with the sa
11To activate an electric motorised screen a 12 Volt output is provided at the rear of the DigiOptic™ Image Processor. This can
12Table 1DigiOptic Image Processor ConnectorY (green) YCr (red)PCb (blue)RYR-YYVPBB-Y UVideo signal source connectorVIDEO 1 2 3 These input
13DVI-D 12This input allows you to advantage from the quality of the digital images.If your source is equipped with a DVI-D outp
14��HDMIFig.12
15 HT300 E-LINK system consists of the Projector and the Di-giOptic™ Image Processor (which is also the system control centre). The
16Typically, the picture will appear after 15-20 seconds. Pressing a key from 1-9 on the remote control selects the corresponding input; pre
177 REMOTE CONTROLThe remote control transmits commands to the system by infrared signals.There are three infrared sensors, one at
18Fig. 18aFig. 18b8 ON SCREEN MENUINPUTSThe input selection menu (Inputs) is called by pressing 0 on the remote control and, when no other
19Temperatura ColoreCorrezione GammaPosizioneOverscanRitardo Y/CFormatoImage1NormaleAnamorficoLetterboxPanoramicoPixel to pixelPersonale 1Pe
LIGHTF1ZOOMFOCUSF2Activates test patternMENU -Activates the On ScreenDisplay menus.Navigates menu pages.FREEZEFreezes a movingpicture.STAND
20COLORThis control (also called Saturation) increases or decreasethe picture colour intensity. When set to zero, colour images will be show
21IMAGEThis menu features adjustments relating to picture position, aspect ratio, etc.ASPECTThis adjustment allows you to change
22up the projected image.These parameters do not normally require adjustment because the system checks the input signal and automatically se
23ORIENTATIONSelect the option that best describes the installation i.e. desktop front, ceiling front, desktop rear and ceiling rear.12CLASS
24In the initial phase of installation the configurable keys (F1, F2) serve as optical zoom and optical focus (Fig.26).POWER ONIf active (AUT
25If you want to delete the modifications use the MENU- key of the remote control.F1/F2 keysThis allows to assign different functions to the
26MEMORIESThe main parameters of the image may be saved in distinct groups of values (known as ‘Memories’); these parameters can subs
27SAVE DEFAULT SETTINGSTo restore the original values to a previously modified Memory, select the line corresponding to the Memory in questio
2810 TROUBLESHOOTING GUIDENo power (Green and red LED are OFF) - Check the power switch at the rear: it must be in position I.- Check if
29- Press A on your remote control or AUTO on keypad to execute automatic adjustments. - Adjust the horizontal and vertical position
31 INTRODUCTIONCongratulations on your choice of the SIM2 Grand Cinema HT300 E-LINK system!12DIGIOPTIC ™LINK CLASS 1 A LASER PRODUCT3-ON
30PROJECTOROPTICAL Projection system: optical engine based on 1 DMD™ DarkChip3 chip, sealed housing, dusty proofDMD™ panel: res
31DIGIOPTIC™ IMAGE PROCESSORELECTRICALInput signals: • 2 COMPOSITE VIDEO (CVBS) RCA type connectors, gold-plated 1.0 Vpp / 75 Ω
32B DIMENSIONS PROJECTORDIGIOPTIC™ IMAGE PROCESSORunit: mm (inches)unit: mm (inches)74 (2-15/16)352 (13-7/8)174 (6-7/8)102 (4)318 (12-1/2)
33 Screen Screen size width (diagonal)
34 Screen Screen size width (diagonal)
35D ON SCREEN MENU LAYOUT Picture Image SetupMenuMemoriesBrightnessContrastColorTintSharpnessFilterCinema Mode Video TypeVideo • S-Video[NT
36 Picture Image SetupMenuMemoriesBrightnessContrastColorTintSharpnessFilterCinema Mode Video TypeVideo • S-Video[NTSC]YCrCb15kHzRGBS 15kHz
37 Picture Image SetupMenuMemoriesBrightnessContrastColorTintSharpnessFilterCinema Mode Video TypeVideo • S-Video[NTSC]YCrCb15kHzRGBS 15kHz
38INDEX1 INTRODUCTION 32 IMPORTANT SAFETY INSTRUCTIONS 53 UNPACKING 8 Package contents 94 INSTALLATION 9 Posi
• Due to the constant product development, specifications and design might be subject to change without notice.SIM2 Multimedia is certifiedSIM
4All image adjustments can be performed with the remote con-trol with the aid of the On Screen Display; alternatively, the unit can be contr
5Prior to switching on the projector please read each chapter of this manual carefully as this manual provides basic instructions for
612111315101412CLASS 1 LASER PRODUCT3-64123958712DIGIOPTIC “LINK CLASS 1 LASER PRODUCT3-1 Projection lens 2 Lens shift knob3 Cooling
7• Read this manual carefully and keep it in a safe place for future consultation. This manual contains important information on how to i
8of electrical storms or when the system will remain unused for prolonged periods. • Avoid contact with liquids and exposure to hu-midity
9The carton should contain the following:- the projector- the DigiOptic™ Image Processor - the remote control- four 1.5V AAA batteries
Kommentare zu diesen Handbüchern