Sim2 SUEPRLUMISHB Betriebsanweisung

SIM2 MultimediaSUPERLUMISECSUPERLUMISHBUser Guide

2 OverviewRemote ControlTurn backlight on for about 5 seconds turns the projector off1-9select inputs and turn the projector on0enters OSD Input m

◦ Memories◦ 3D Controls (3D Mode and Input Formats)OperationThe SUPERLUMIS projector has two IR receivers, one on the front and one on the back of the

Connections❶ ❷ ❸ ❹ ❺ ❻❼ ❽Inputs❶HDMI 1HDMI 2Accept both HDMI and DVI digital video inputs.❷Components/RGB-HV Four RCA connectors. They accept both sta

3D RF EmitterThe 3D RF emitter is designed to be placed near the projector and aimed at the screen. It receives the 3D sync signal from the pro

3 InstallationThis section provides instructions for the installation of the SUPERLUMIS projector.Important: Installation procedures should be perform

Ceiling MountingInvert the projector and suspend it from the ceiling using a specific bracket.• To fit the bracket unscrew and remove the 3 rubber fee

If it is not possible to position the projector perpendicular to the projection screen (so that the lens center and screen center are aligned with eac

throughout the entire signal path◦ highest available resolution, because video sources can deliver full resolution content via HDMI only◦ availability

Note: RS-232 communications are limited to 15 m (50 ft.), whereas USB are limited to 5 m (16 ft.).TriggersSome Home Theater devices can be controlled

Charging the batteryThe glasses are shipped with the micro USB to USB Type A cable. To charge the glasses battery, plug the micro USB cable in a compu

Contents3 Important informationAbout this User GuideSafety3D contentEnvironmentNotice7 Chapter 1: IntroductionKey Features and BenefitsSystem Componen

4 OperationViewing 3D Content3D stereo visualization offers clear and sharp 3D images thanks to 3 chip DLP Imaging technology. This technique achieves

select the correct one.• Switch on your 3D glasses. Refer to the instructions supplied with the glasses to ensure correct operation.• The projector wi

• 2D display mode for normal 2D material. 3D Input Format adjustment is unavailable. PureMotion adjustment is available.3D Input FormatThe SUPERLUMIS

Table 4.1Signal 3D Format HDMI 1.4a DVB1920 x 1080p @ 23.98/24 Hz Frame Packing YesSide by Side YesTop and Bottom Yes Yes1920 x 1080p @ 25 Hz Side by

• To enter the Input menu press:Key 0 on the remote control or Source on the projector keypad.• To select an input press the corresponding number on t

PictureThis menu section provides access to common image quality adjustments. Adjustments not available for a given input are not displayed in the men

ColorThis control (also called Saturation) increases or decreases the picture color intensity. When set to zero, color images are shown in black and w

DynamicBlackThis function improves the level of black and increases the depth and the detail of the image especially in parts with low and medium brig

• Letterbox displays a 4:3 letterbox image (source signal with black bands above and below the picture) in such a way that it fills the 16:9 screen an

◦ User a white point that can be adjusted according to your personal preferences as follows:▪ press the number 3 on the remote control to activate the

Important informationAbout this User GuideThis User Guide describes how to set up and operate the following projectors:• SUPERLUMISEC• SUPERLUMISHBExc

on the remote control to activate the automatic adjustment function. If the automatic procedure fails to achieve the required effect, enter the Freque

To set the custom settings for zoom, focus, vertical and/or horizontal shift is necessary to enter the SETUP menu, Projection Lens or more quickly by

MenuThis menu section provides access to OSD adjustments.LanguageSelects the desired OSD language. The SUPERLUMIS can display the menus in English, It

Source InformationWhen enabled (Yes), the projector displays information about the current input signal every time a new signal is detected. If disabl

MemoriesYou can store and recall at a later time up to six different sets of values (Memories) per input type, so that you have customized setups for

desired, repeat the steps above to save additional memories in different locations.Note: You can change the name of each memory. See “Rename” below fo

InfoDisplays a summary of the projector settingsThis function is displayed by pressing Info on the remote control.Quick MenusThe quick menus provide a

5 TroubleshootingThe projector does not turn on• Make sure the main power switch (at the rear of the projector) is in the On position.• Ensure the pro

3D content is displayed as two near-identical images• If they are next to each other, press the 3D key on the remote control and then choose Side by S

6 SpecificationsProjection Type Digital Light Processing (DLP), 3-chipDLP Type: 0.95 in., 1920 x 1080, DC4Optical Engine Die cast, based on SIM2 paten

electrical supply with rated voltage of between 100-240 V AC, 50/60 Hz and equipped with a protective earth connection. If you are not sure of your do

Video Standards  Composite: NTSC 3.58/4.43, PAL B/G/H/I/M/N/60, SECAM (automatically selected) Components/RGBHV: 480i, 576i, 480p, 576p, 1080i 50/60

7 Projection Distances1.78:1 (16:9) ScreenScreenProjection DistanceVerticalOffset(m)T1 (1.37-1.66:1)T2 (1.82÷2.48:1) T3 (2.6÷3.90:1)Diagonal Size (in.

8 DimensionsSUPERLUMIS dimensions in millimeters and (inches).8 Dimensions SUPERLUMISUser Guide42

SIM2 Multimedia S.p.a.Viale Lino Zanussi, 11 33170 Pordenone – ITALYPhone: + 39 0434 383256 Fax: +39 0434 383260Email: [email protected] US

Never look directly at the projection lampNever look directly into the lens when the lamp is on as the intense light may damage your eyes. Take partic

• When you no longer wish to use your electrical and electronic equipment, take it to your local waste disposal facility for recycling.• You may retur

These limits are perfectly normal for this optical system and will not be considered as a malfunction of the product.Note: One pixel corresponds to 10

1 IntroductionThe SUPERLUMIS is a high-end compact 3-chip DLP 3D single unit projector that utilizes SIM2’s state-of-the-art optical technologies to p

• 3 x jacks for 12 V output connectors• 1 x 4.0-millimeter Hex wrench (for lens shift adjustment)• 1 x User guide (this document)If any items are miss