Sim2 C3X Lumis Installationshandbuch PDF herunterladen (Seite 5)

C3X Lumis

ENGLISH

lation operations. Pull the plug, not the cable, to disconnect

the unit from the mains. Use only the speciﬁed power supply.

Connect the units to a mains electrical supply with rated voltage

of between 100-240 VAC, 50/60 Hz and equipped with a protec-

tive earth connection. If you are not sure of your domestic mains

rating, contact an electrician. Take care to avoid overloading the

power socket and any extension leads.

Switching the projector off

Pay attention to the switch off procedure for the projector. The

system must always be brought back to the stand-by state to

allow the projector to carry out the cooling procedure. Should

this not happen, for example due to a power cut, the projector

may enter a state of protection which leads to switch-on being

blocked.

This block will last until the internal components of the system

have completely cooled down.

Changing the fuses.

Before changing the fuse, disconnect the unit from the mains

power supply. The fuse compartment is next to the power supply

connector. Remove the fuse holder with a ﬂat head screwdriver

and replace the fuse. Fit the replacement fuse. Use only type T

10A L H fuses for the projector.

Be careful with cables.

Make certain cables are routed so that people will not be im-

peded or tripped up. Keep all cables away from children. Install

the unit as close to the wall socket as possible.

Avoid stepping on power cables, make certain they do not be-

come tangled, and never jerk or tug them; do not expose them

to sources of heat, and make sure they do not become knotted

or crimped.

If the power cables become damaged, stop using the system

and request the assistance of an authorised technician.

Disconnect the unit from the mains power during electri-

cal storms and when not in use.

To prevent damage from lightning strikes in the vicinity, discon-

nect the unit during storms or when the system is going to be

left unused for a long time.

Avoid contact with liquids and exposure to damp.

Do not use the unit near water (sinks, tubs, etc.); do not place

objects containing liquids on or near the units and do not ex-

pose them to rain, humidity, drops of water or sprays; do not

use water or liquid detergent to clean them.

Place the unit on a stable surface.

Place the projector on a stable surface or use the ceiling

mounting bracket provided. Never place the projector on its

side or rear, on the lens or top panel.

Avoid contact with liquids and exposure to damp.

Connect the unit to the mains as shown in the ﬁgure.

Do not allow the units to overheat.

To prevent overheating, allow a free space of at least 20 cm

at the back of the projector. Do not obstruct the ventilation

slots. Do not place the unit near heat sources such as heaters,

radiators or other devices (including ampliﬁers) that generate

heat. Do not place the unit in an area where there is insufﬁcient

space (shelving units, bookshelves, etc.) and in general avoid

placing it in poorly ventilated areas as this may prevent suf-

ﬁcient cooling.

Never look directly at the projection lamp.

Never look directly at the objective lens when it is on as the

intense light may damage your eyes. Take particular care that

children cannot do so.

Take special care regarding movement of the lens.

Do not place objects in the slots on the side of the lens, and

also ensure that vertical lens movements are not impeded by

external objects.

Do not insert objects through the openings in the unit.

Make sure that no objects are inserted inside the units. If this

should occur, disconnect the unit from the power supply im-

mediately and call an authorised technician.

Power saving.

We advise disconnecting the unit from the power supply when

not in use. In this way you will achieve considerable power sav-

ings while at the same time protecting internal electrical parts

from wear.

PRODUCT DISPOSAL

This projector is ﬁtted with a pressurised lamp contain-

ing a small amount of mercury. These lamps may be sub-

ject to special disposal regulations due to environmental

considerations. For disposal or recycling information,

please contact your local authorities or, if you are locat-

ed in the USA, the Electronic Industries Alliance.

www.eiae.org

www.lamprecycle.org

FUSE T1

10A L H 250V~

100-2 40 Va c

50/60 Hz

1 2 3 4 5 6 7 8 9 10 ... 30 31

Kommentare zu diesen Handbüchern

Keine Kommentare

Sim2 C3X Lumis Installationshandbuch Seite 5

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Datenprojektoren Sim2 C3X Lumis